Wings Forum Forum for homebuilt experimental & light sport aircraft pilots, owners, & builders.   Buttercup Leading Edge ( Mike ) Click here to go to the original topic          Wings Forum Forum Index -> Wittman Aircraft View previous topic :: View next topic   Author Message planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Sat Sep 27, 2008 12:49 pm    Post subject: Buttercup Leading Edge ( Mike )   Hey Guys,                Gathering material to start this Stage.... I bought a Sheet 4ft X 10ft  of .032 - 6061-T6 Aluminum I'll be using that to make the Channels that run the full length of the leading edge. and I'll be making the Rib shapes out this material too....  I ordered two rolls of leading edge material - 2024-T3   from ACS  P/N  03-30850 Comes 12in wide or 18in wide....I ordered 18in X 12ft , They were $48.75 ea "BUT" this stuff is only  .016  ( calls for  .020 ) So I'll be watching to see if this will need a packing foam injected into the empty compartments of the leading edge....      I already got my pieces cut and the angles bent for the Hinge bracket that fits inside the leading edge Channel .... But I'll wait on building those until my Channel is Formed that way I'll get a perfect fit-up...                 OK,  That's it for now...                                                  Gotta Fly...                                                                  Mike & "Jaz" in MN PS  I ordered 14ft of 1/2 X .035 Chromemoly for the Flap/leading edge control tubes.... They weren't on the material list... I told ACS to cut them at 3ft 6in  ea             Back to top   planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Mon Sep 29, 2008 6:24 pm    Post subject: Leading Edge "channels"   Hey Guys,               I cut off a piece of my Sheet of 6061T6... I used a straight edge and my new "Nibbler" I cut off enough to shear two pieces 9ft 3in X 6.25 in  ( 6.25 is the "Stretch Out" for bending my Channel )  The Channels look perfect.... A Buddy of mine made them to my dimensions ...          Here's some pictures...                                              Gotta Fly...                                                              Mike & "Jaz" in MN PS  ACS shipped my 2024T3 today... Back to top   planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Thu Oct 02, 2008 6:16 pm    Post subject: Form Blocks   Hey Guys,               I made some "Form Blocks" for the rib sections in the Leading edge....  I made two.... It will help hold the Rib piece better , also some have to be "reversed" on the Ends of the leading edge...  I might reverse more just for strength , instead of having them all the same way...  I got my Leading edge material today.... I'm not going to unroll it until I need to use it...                                     Gotta Fly...                                                     Mike & "Jaz" in MN Back to top   planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Sat Oct 04, 2008 7:03 pm    Post subject: Leading edge "Ribs"   Hey Guys,               I've got some Ribs formed... Here's some pictures.                                  Gotta Fly...                                                  Mike & "Jaz" in MN . . . Back to top   planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Tue Oct 07, 2008 6:02 pm    Post subject: Leading Edge progress   Hey Guys,                I got both Channels "layed out" and Drilled... I've got the Rib sections on one Channel with Cleco's...                                                 Gotta Fly...                                                                 Mike & "Jaz" in MN . . . Back to top   planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Fri Oct 10, 2008 6:52 pm    Post subject: Leading edge "Ribs"   Hey Guys,                I have the Ribs Riveted to the Channel.... I made 12 Ribs one way , and 12 opposite This way they should be stronger... I think I need to start on the Hinge area now....                                                      Gotta Fly...                                                                      Mike & "Jaz" in MN . . . Back to top   planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Sun Oct 19, 2008 7:59 am    Post subject: Hinges   Hey Guys,                I was out in the garage a little yesterday... I got some work done on the hinges...                      Got more to do... Here's some pictures                                                      Gotta Fly...                                                                        Mike & "Jaz" in MN . . Back to top   planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Sun Oct 19, 2008 6:03 pm    Post subject: Hinges   Hey Guys,                I've got the Wing hinge ready to mount before I drill the Pivot Hole... The tabs that the hole gets drilled into were made to the dimensions... But there just too long.   Once I figure where the hole goes , I'll trim them down...                                                    Gotta Fly...                                                                    Mike & "Jaz" in MN . . . Back to top   planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Sun Nov 09, 2008 11:58 am    Post subject: Hinges   Hey Guys,              I mounted the "Leading Edge" Hinges on the Front spar.... Something I didn't understand before was ...Why they have the Pivot point "Tab" so big??? I'll have to trim them all up later... I took a picture of the aprox position of the hole/pivot point. Looks like I need to make the arm assembly that fits into the leading edge next.  Here's some pictures...                                                 Gotta Fly...                                                                 Mike & "Jaz" in MN . . . Back to top   planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Fri Nov 28, 2008 11:52 am    Post subject: Leading Edge pivot arms   Here's a picture of the Leading Edge Pivot Arms... They also have the pivot tabs too long... I'll have to reshap both sides again. Back to top   planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Fri Nov 28, 2008 11:56 am    Post subject: Leading Edge pivot arms   I've got the Leading Edge clamped into it's position... I've marked where to slot the Channel to clear the Leading Edge Pivot Arm... Once I cut that out.... I can start fitting the Hinge assy into the Channel before welding...                                                                   Gotta Fly... . . . Back to top   planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Sat Nov 29, 2008 6:50 pm    Post subject: Hinges in place   Hey Guys,                 I've got the Hinges in place... I still need to put the angle for the control arm in place... But the leading edge has it's pivot point done....                                                                       Gotta Fly... . . . Back to top   planecrazzzy Joined: 01 Jan 2005 Posts: 207 Location: Minnesota Posted: Sun Nov 30, 2008 3:54 pm    Post subject: Hinge/ Control brace   Hey Guys,                Since I fudged the Ailerons towards the Flaps.... I needed to fudge the control brace on the Leading Edge Hinge assy.... It's supposed to be 2  1/4"  from the end of the angle.... I've got it at 2"  I think my control rod will end up straight now.... The inboard Hinge assy can stay like it is....                                                                Gotta Fly...                                                                                Mike & "Jaz" in MN . . . Back to top            Wings Forum Forum Index -> Wittman Aircraft Page 1 of 1 Powered by phpBB Search Engine Indexer Powered by phpBB 2.0.22 © 2001, 2002 phpBB Group