I'm getting ready for the painting process and was wondering what you guys did for fresh air? Did you use a breather unit or just a face mask? I find the $1k units that are hvlp are really expensive for one paint job but cool for my lungs. Just wondering what set ups you guys have or will be using?
Thanks,
Paul, PA
Painting
- stede52
- Premium Member
- Posts: 1066
- Joined: Thu Sep 06, 2007 11:40 am
- Location: Carnation, WA
I know the polytone and Stuart Systems (water based) require only a good respirator mask. The aerothanes top coats and superflite system require a fresh air system which is the case for most two part urethane paints except for the water based systems. I happen to have a turbine paint compressor which comes with a fresh air attachment.
Steve
Steve
-
- Veteran Member
- Posts: 282
- Joined: Mon Aug 14, 2006 11:53 am
- Location: Orwigsburg, PA
I was going to go with Poly Fiber but am sticking with Superflite. They recommend a fresh air system but I know of at least 1 person who used just a mask. I'd like to find a place that rents the combo units but can't find anyone online that does. Their about a grand to buy and having never painted before, I am having a hard time justifying the cost for a one time project.
Also, is it wise to paint in an attached garage with those nasty isocyanates (spelling?) being right next door? I plan to add the plastic, a fan and filter etc. but wanted your opinions. I like it in there because the temperature is nice and regulated. My workshop is very moody and has gotten up to 90 degrees already this spring on warm days. Down to the 40's at night. Also, I have 2 young kids, the wife, a dog, etc. to be concerned about.
Paul, PA
Also, is it wise to paint in an attached garage with those nasty isocyanates (spelling?) being right next door? I plan to add the plastic, a fan and filter etc. but wanted your opinions. I like it in there because the temperature is nice and regulated. My workshop is very moody and has gotten up to 90 degrees already this spring on warm days. Down to the 40's at night. Also, I have 2 young kids, the wife, a dog, etc. to be concerned about.
Paul, PA
-
- New Member
- Posts: 18
- Joined: Sat Feb 16, 2008 8:02 pm
- Location: wisconsin
I have a turbine system that allows for fresh air. I love it. For many years I used a conventional spray gun for the nasty 2 parts. I've had chemical pneumonia twice from painting without the fresh air setup while using a mask. I would not paint in an attached garage. (I have, but I was single at the time) It is near impossible to keep the fumes out of the house.
I've painted friends projects. They did all the prep, I went over and did the paint, they bought the beer. Check with your EAA chapter. You might find someone to help you out.
Dan
I've painted friends projects. They did all the prep, I went over and did the paint, they bought the beer. Check with your EAA chapter. You might find someone to help you out.
Dan
-
- New Member
- Posts: 17
- Joined: Sat Jun 23, 2007 10:24 am
- Location: New Orleans
Has anyone paid a paint shop to paint their aircraft? Can a typical paint shop handle the job or do you have to find someone used to aircraft? I would like to know what a reasonable cost might be and whether there are any other issues. My only other option is to build a paint booth on my front lawn.
Prescott
- Stan Bearup
- Forum Regular
- Posts: 43
- Joined: Thu Sep 08, 2005 1:30 pm
- Location: American Falls, Idaho
- Contact:
Painting fabric is a little different than painting cars, or metal airplanes, but not a lot different. It's pretty simple to do, as long as you follow the application instructions and steps correctly. If you decide to build a paint booth, check out the link below, where you can purchase a tarp type tent garage. They work really well for this. I have seen them at Sam's Club for $150 - $200. Once your done using it as a paint booth, you can use it as a tool shed, car storage shed, or just sell it on Craig's List.
http://www.screen-house.com/harnios_xr_12.htm
Stan
www.justkitplanes.com
http://www.screen-house.com/harnios_xr_12.htm
Stan
www.justkitplanes.com