Tundra Lite Tailwheel by Jim Pekola
- stede52
- Premium Member
- Posts: 1066
- Joined: Thu Sep 06, 2007 11:40 am
- Location: Carnation, WA
Re: Tundra Lite Tailwheel by Jim Pekola
Syd,
You are correct about one more thing to do, however, when you think about it this task is not being done during a high activity time, it could easily be done as part of your take-off check list as the airplane is stationary and straight and after the landing roll out at which time you are almost stopped. Just a thought . Even if you didn't go with the locking tailwheel, I would still buy it over the matco.
You are correct about one more thing to do, however, when you think about it this task is not being done during a high activity time, it could easily be done as part of your take-off check list as the airplane is stationary and straight and after the landing roll out at which time you are almost stopped. Just a thought . Even if you didn't go with the locking tailwheel, I would still buy it over the matco.
Steve D N419LD
- kenryan
- Veteran Member
- Posts: 342
- Joined: Sat Jan 01, 2011 3:46 pm
- Location: anchorage, ak
Re: Tundra Lite Tailwheel by Jim Pekola
I have requested the Tundra Lite for my SuperStol (hopefully to ship June 1 !) Steve, I was wondering how you go about setting the tension, and how frequently it needs to be readjusted.
Super Stol Kit #299
- stede52
- Premium Member
- Posts: 1066
- Joined: Thu Sep 06, 2007 11:40 am
- Location: Carnation, WA
Re: Tundra Lite Tailwheel by Jim Pekola
Jim sets the tension and so far I like where its set. I have tried other stiffer setting but needed more brake to turn. Try Jim's setting first and fly it for a while and then try making small adjustments. Flying it or taxing it for a while will give you a baseline feel to compare with other settings. I think you'll probably like the initial setting.kenryan wrote:I have requested the Tundra Lite for my SuperStol (hopefully to ship June 1 !) Steve, I was wondering how you go about setting the tension, and how frequently it needs to be readjusted.
Steve D N419LD
-
- New Member
- Posts: 12
- Joined: Fri Apr 26, 2013 9:33 pm
Re: Tundra Lite Tailwheel by Jim Pekola
Thanks for that gents..
- Tralika
- Veteran Member
- Posts: 386
- Joined: Thu Oct 08, 2009 12:49 pm
- Location: Wasilla Alaska
Re: Tundra Lite Tailwheel by Jim Pekola
Locking Tailwheel
I've never flown a Highlander so I don't know how it handles on the ground. I do fly C-185's and they can be a handful if you don't keep it going straight down the runway. A locking tailwheel is pretty nice to have in a gusty crosswind. It also eliminates tailwheel shimmy.
I've never flown a Highlander so I don't know how it handles on the ground. I do fly C-185's and they can be a handful if you don't keep it going straight down the runway. A locking tailwheel is pretty nice to have in a gusty crosswind. It also eliminates tailwheel shimmy.
John Nealon
Wasilla, Alaska
Highlander Extreme #191
mykitlog.com/jnealon
Wasilla, Alaska
Highlander Extreme #191
mykitlog.com/jnealon
- stede52
- Premium Member
- Posts: 1066
- Joined: Thu Sep 06, 2007 11:40 am
- Location: Carnation, WA
Re: Tundra Lite Tailwheel by Jim Pekola
I'm hoping we can get a first hand report from John Levy on his tailwheel training with Jim Pekola's lockable tailwheel. I was talking with Troy yesterday and John's CFI was so impressed with it, as a training tool for new tailwheel pilots, that he thought they should be supplied on every Highlander going out of the factory
Steve D N419LD
- mac
- Seasoned Member
- Posts: 60
- Joined: Sun Jul 29, 2012 7:57 pm
- Location: Grass Valley, CA.
Re: Tundra Lite Tailwheel by Jim Pekola
Steve:
Do you know of anyone (and/or Jim), who has come up with a real good cable/handle/mechanism for the locking portion of the Perkola tailwheel? I've come up with several ideas and locations to mount such a control handle, but haven't considered anything a winner yet.
Also, wondering if anyone has integrated a spring "return" of sorts, such that when a handle in placed in the "engage" or locked position, the locking pin slips into place once the airplane and tailwheel are aligned..............as in a final turn onto the runway from a taxiway.
At this point, just looking for ideas. Got any?
Thanks.
Do you know of anyone (and/or Jim), who has come up with a real good cable/handle/mechanism for the locking portion of the Perkola tailwheel? I've come up with several ideas and locations to mount such a control handle, but haven't considered anything a winner yet.
Also, wondering if anyone has integrated a spring "return" of sorts, such that when a handle in placed in the "engage" or locked position, the locking pin slips into place once the airplane and tailwheel are aligned..............as in a final turn onto the runway from a taxiway.
At this point, just looking for ideas. Got any?
Thanks.
Mark M.
N49SS in Phase 2....for good!
N49SS in Phase 2....for good!
- gkremers
- Veteran Member
- Posts: 495
- Joined: Sun Aug 08, 2010 8:06 am
- Location: Michigan
Re: Tundra Lite Tailwheel by Jim Pekola
Mark,
It's not a new idea but I'm using the trim handle location as my trim is electric. I've already run the cable and modified the inspection plate on the lower aft section of the fuselage.
Gary
It's not a new idea but I'm using the trim handle location as my trim is electric. I've already run the cable and modified the inspection plate on the lower aft section of the fuselage.
Gary
- stede52
- Premium Member
- Posts: 1066
- Joined: Thu Sep 06, 2007 11:40 am
- Location: Carnation, WA
Re: Tundra Lite Tailwheel by Jim Pekola
Mark,
check out page 3 of this subject, we talk about the handle options and why the spring is no longer needed.
check out page 3 of this subject, we talk about the handle options and why the spring is no longer needed.
Steve D N419LD
- mac
- Seasoned Member
- Posts: 60
- Joined: Sun Jul 29, 2012 7:57 pm
- Location: Grass Valley, CA.
Re: Tundra Lite Tailwheel by Jim Pekola
Thanks Steve. I did see that info a few months ago and probably should have just gone with that. Was looking for some more up-to-date concepts, potential changes, problems, etc. Would be nice if Jak would post a picture of what they are doing at the factory with the locking mechanism, especially with the control end portion........in the cockpit.
Regardless....should be able to figure it out from the previous discussions. Thanks again.
Regardless....should be able to figure it out from the previous discussions. Thanks again.
Mark M.
N49SS in Phase 2....for good!
N49SS in Phase 2....for good!
- stede52
- Premium Member
- Posts: 1066
- Joined: Thu Sep 06, 2007 11:40 am
- Location: Carnation, WA
Re: Tundra Lite Tailwheel by Jim Pekola
Mark,
I talked to Jim Pekola today and he's giving the question some thought. I know John Levy, with the Camo Highlander has Pekola's lockable tail wheel, maybe when his airplane lands in New Zealand in 4- 6wks he can get us some pics of his install.
I talked to Jim Pekola today and he's giving the question some thought. I know John Levy, with the Camo Highlander has Pekola's lockable tail wheel, maybe when his airplane lands in New Zealand in 4- 6wks he can get us some pics of his install.
Steve D N419LD
-
- Veteran Member
- Posts: 445
- Joined: Mon Mar 17, 2008 9:40 pm
- Location: toccoa Ga
Re: Tundra Lite Tailwheel by Jim Pekola
Mac we've only put in one lockable and we did the same thing Gary did as it had elec. trim. Haven't come up with anything else yet. Jak
Pick up a rifle and you instantly change from a subject to a citizen.
- Tralika
- Veteran Member
- Posts: 386
- Joined: Thu Oct 08, 2009 12:49 pm
- Location: Wasilla Alaska
Re: Tundra Lite Tailwheel by Jim Pekola
Think there's any way to make the tailwheel locking lever from some kind of bicycle brake lever attached to the flap handle? I just did a quick google search for locking bicycle brake lever and came up with dozens of products. There are even light weight versions made for mountain bikes.
John Nealon
Wasilla, Alaska
Highlander Extreme #191
mykitlog.com/jnealon
Wasilla, Alaska
Highlander Extreme #191
mykitlog.com/jnealon
-
- Veteran Member
- Posts: 304
- Joined: Sun Jul 01, 2012 11:59 am
- Location: Big Bear Airport
Re: Tundra Lite Tailwheel by Jim Pekola
I just figured out how to post a video (I think) and am reviving this post to show you the Tundra Lite TW in action. Mine is the non-locking version.
http://vimeo.com/90432812
It's nice and smooth. Next time out I'm going to start practicing landing and coming to a stop without using the brakes. It's a skill I want to develop with a non-steerable TW. Shouldn't be a problem, if the tension is correct on the pivot it tracks perfectly.
http://vimeo.com/90432812
It's nice and smooth. Next time out I'm going to start practicing landing and coming to a stop without using the brakes. It's a skill I want to develop with a non-steerable TW. Shouldn't be a problem, if the tension is correct on the pivot it tracks perfectly.
GDS
So Cal
Highlander #232
Rotax 912ULS, Dynon Skyview
So Cal
Highlander #232
Rotax 912ULS, Dynon Skyview
-
- Veteran Member
- Posts: 254
- Joined: Sat Dec 15, 2012 3:50 pm
Re: Tundra Lite Tailwheel by Jim Pekola
Howdy Everyone, Yep I highly recommend Jim's tail wheel but I don't think I would go for the lockable tail wheel again. My decision in getting that option was has a newbie tailwheel pilot, and for the first couple of hours I did use it. However I soloed the airplane in just a few hours, and I have not used it since. I used the manual elevator lever to lock the tail wheel as I installed a electric trim. However I would leave the manual trim as it gives greater authority. Just MHO