Bottom Stringer Question

For general discussion of the Just Aircraft family of aircraft.
Includes: Highlander, Escapade, Summit and SuperSTOL.

Moderator: scubarider2

Bottom Stringer Question

Postby sonex293 » Wed Aug 19, 2015 10:16 pm

Finally getting to the bottom stringer installation. The builder's manual calls for

"The forward end of the stringer tube will need to be flattened against the fuselage bottom/first bushing; otherwise it will interfere with the top of nose gear leg."


Since we're currently going with a nose wheel ( yea I know! ), my build partner and I are trying to understand the interference piece. We just don't see how the bottom stringer will interfere with the "top of the nose gear leg". Maybe we're just missing something.

Any insight? Pictures?

==
Michael
Building Highlander #371
http://highlander371.blogspot.com/
User avatar
sonex293
Veteran Member
 
Posts: 104
Joined: Sat Aug 28, 2004 9:18 am
Location: Cary, NC

Re: Bottom Stringer Question

Postby Johnny C! » Thu Aug 20, 2015 9:59 pm

Michael,
I am one of those "other guys"
too. I built Lima Charlie as a
trike, as well.

I don't remember that from
my build, but I will look in
that area tomorrow morning
to see if I can help.

John
There are many things that happen really fast when you are
flying an airplane. There is no sense in rushing any of the others.

I would much rather be looking down at the runway, than up at it.

Duane Sorenson & Rick Norton Gone West 6/8/09. Godspeed
User avatar
Johnny C!
Veteran Member
 
Posts: 820
Joined: Thu Sep 07, 2006 9:55 am
Location: Brevard, NC

Re: Bottom Stringer Question

Postby sonex293 » Thu Aug 20, 2015 10:07 pm

Awesome, thanks!

==
Michael
Building Highlander #371
http://highlander371.blogspot.com/
User avatar
sonex293
Veteran Member
 
Posts: 104
Joined: Sat Aug 28, 2004 9:18 am
Location: Cary, NC

Re: Bottom Stringer Question

Postby Johnny C! » Sat Aug 22, 2015 11:40 pm

We have had a death in the family.

It may be a few days before I can
make it to the hangar.

Sorry.

John
There are many things that happen really fast when you are
flying an airplane. There is no sense in rushing any of the others.

I would much rather be looking down at the runway, than up at it.

Duane Sorenson & Rick Norton Gone West 6/8/09. Godspeed
User avatar
Johnny C!
Veteran Member
 
Posts: 820
Joined: Thu Sep 07, 2006 9:55 am
Location: Brevard, NC

Re: Bottom Stringer Question

Postby sonex293 » Sun Aug 23, 2015 8:12 am

No Problem.....

==
Michael
Building Highlander #371
http://highlander371.blogspot.com/
User avatar
sonex293
Veteran Member
 
Posts: 104
Joined: Sat Aug 28, 2004 9:18 am
Location: Cary, NC

Re: Bottom Stringer Question

Postby Johnny C! » Fri Aug 28, 2015 10:50 pm

I looked on the inside tonight, but I forgot to
look on the outside. I think the biggest thing
is to make sure the stringer is above the
firewall frame so it does not protrude after
covering.

I will look at the outside in relation to the
nose gear mount tomorrow.

John
There are many things that happen really fast when you are
flying an airplane. There is no sense in rushing any of the others.

I would much rather be looking down at the runway, than up at it.

Duane Sorenson & Rick Norton Gone West 6/8/09. Godspeed
User avatar
Johnny C!
Veteran Member
 
Posts: 820
Joined: Thu Sep 07, 2006 9:55 am
Location: Brevard, NC

Re: Bottom Stringer Question

Postby Johnny C! » Tue Sep 01, 2015 12:55 pm

Sorry for the delay again.

I don't see anyway that the stringer
and it's spigot could interfere with
the nose gear bracket. I would have
to assume that the description is in regards
to an earlier design, and perhaps it has
been corrected on the airframe, but the
old comments remain in the manual.

John
There are many things that happen really fast when you are
flying an airplane. There is no sense in rushing any of the others.

I would much rather be looking down at the runway, than up at it.

Duane Sorenson & Rick Norton Gone West 6/8/09. Godspeed
User avatar
Johnny C!
Veteran Member
 
Posts: 820
Joined: Thu Sep 07, 2006 9:55 am
Location: Brevard, NC

Re: Bottom Stringer Question

Postby sonex293 » Tue Sep 01, 2015 1:15 pm

Thanks for looking. That is what we figured. We just couldn't find any interference issues. Bottom Stringer is now installed and we're moving on.

Thanks Again,
Michael
Building Highlander #371
http://highlander371.blogspot.com/
User avatar
sonex293
Veteran Member
 
Posts: 104
Joined: Sat Aug 28, 2004 9:18 am
Location: Cary, NC


Return to Just Aircraft

cron