Bottom Stringer Termination - SS
-
- Veteran Member
- Posts: 356
- Joined: Wed Oct 07, 2015 11:40 am
- Location: Cave Creek, AZ
Bottom Stringer Termination - SS
Can someone post a pic of how you terminated the bottom stringer at the rear? This is for a SuperSTOL.
Thanks,
Clark
Thanks,
Clark
Building SuperSTOL Kit 512
Cave Creek, AZ
Cave Creek, AZ
- BDA
- Veteran Member
- Posts: 707
- Joined: Mon Aug 22, 2016 11:25 am
- Location: Kenai Alaska
Re: Bottom Stringer Termination - SS
Sorry my photo is not very good, you can kind of see that it bends up right after the last stand off, to come inside the fuselage just in front of the next cross tube. Stretch a sheet over it to check your lines.
Remember, any liquid spilled will follow this sringer.
Remember, any liquid spilled will follow this sringer.
You do not have the required permissions to view the files attached to this post.
SuperStol XL Alaskan With Titan 340
N331AK. Shawn Taplin
Wing extensions,Symetrical Airfoil tail ribs (NACA 21)
Mods in progress: Heavier struts, Double slotted flaps
Goal: 15mph no wind
N331AK. Shawn Taplin
Wing extensions,Symetrical Airfoil tail ribs (NACA 21)
Mods in progress: Heavier struts, Double slotted flaps
Goal: 15mph no wind
-
- Veteran Member
- Posts: 356
- Joined: Wed Oct 07, 2015 11:40 am
- Location: Cave Creek, AZ
Re: Bottom Stringer Termination - SS
Thanks! Does this look OK, too long, or should i bend it up more?
Thanks,
Clark
Thanks,
Clark
You do not have the required permissions to view the files attached to this post.
Building SuperSTOL Kit 512
Cave Creek, AZ
Cave Creek, AZ
- BDA
- Veteran Member
- Posts: 707
- Joined: Mon Aug 22, 2016 11:25 am
- Location: Kenai Alaska
Re: Bottom Stringer Termination - SS
Cant tell from the picture
Isnt there another standoff on the next cross tube?
Isnt there another standoff on the next cross tube?
SuperStol XL Alaskan With Titan 340
N331AK. Shawn Taplin
Wing extensions,Symetrical Airfoil tail ribs (NACA 21)
Mods in progress: Heavier struts, Double slotted flaps
Goal: 15mph no wind
N331AK. Shawn Taplin
Wing extensions,Symetrical Airfoil tail ribs (NACA 21)
Mods in progress: Heavier struts, Double slotted flaps
Goal: 15mph no wind
-
- Veteran Member
- Posts: 356
- Joined: Wed Oct 07, 2015 11:40 am
- Location: Cave Creek, AZ
Re: Bottom Stringer Termination - SS
Nope. The ELT tray tabs are there.
*Edit* Here is a little better pic...
*Edit* Here is a little better pic...
You do not have the required permissions to view the files attached to this post.
Building SuperSTOL Kit 512
Cave Creek, AZ
Cave Creek, AZ
- BDA
- Veteran Member
- Posts: 707
- Joined: Mon Aug 22, 2016 11:25 am
- Location: Kenai Alaska
Re: Bottom Stringer Termination - SS
Ok
Thats how they say to do it
Yes maybe a little long
I left mine really long, ran it all the way back to the tab for the ELT so it had suport, just liked that look better. The screw that holds the ELT plate also screws into the stringer.
What you have there works just fine, wrap a sheet over it to see where it is not touching the tube anymore and cut it an inch or 2 longer, so the end wont contact fabric.
Thats how they say to do it
Yes maybe a little long
I left mine really long, ran it all the way back to the tab for the ELT so it had suport, just liked that look better. The screw that holds the ELT plate also screws into the stringer.
What you have there works just fine, wrap a sheet over it to see where it is not touching the tube anymore and cut it an inch or 2 longer, so the end wont contact fabric.
SuperStol XL Alaskan With Titan 340
N331AK. Shawn Taplin
Wing extensions,Symetrical Airfoil tail ribs (NACA 21)
Mods in progress: Heavier struts, Double slotted flaps
Goal: 15mph no wind
N331AK. Shawn Taplin
Wing extensions,Symetrical Airfoil tail ribs (NACA 21)
Mods in progress: Heavier struts, Double slotted flaps
Goal: 15mph no wind
- SheepdogRD
- Proprietor
- Posts: 930
- Joined: Tue Nov 30, 2010 5:41 pm
- Location: West of Atlanta, GA
Re: Bottom Stringer Termination - SS
Yep, I ran mine all the way back, too. Mine goes just short of the crossmember at the tailwheel pivot. I put a rivet nut in the top of the stringer, right at the end. A 6-32 x 3/8" screw goes down through the ELT mount and into that rivet nut, locking the stringer in place.BDA wrote:I left mine really long, ran it all the way back to the tab for the ELT so it had suport, just liked that look better.
Richard Holtz
Highlander N570L -- Ms. Tonka -- in gestation
If just enough is really good, then too much ought to be perfect.
Highlander N570L -- Ms. Tonka -- in gestation
If just enough is really good, then too much ought to be perfect.
-
- Veteran Member
- Posts: 356
- Joined: Wed Oct 07, 2015 11:40 am
- Location: Cave Creek, AZ
Re: Bottom Stringer Termination - SS
Thanks guys, Jak got back with me and said I had it correct. I don't know why they just don't weld a stud on the last cross bar under the ELT tab to plug into? It would take all the guess work out of it.
Clark
Clark
Building SuperSTOL Kit 512
Cave Creek, AZ
Cave Creek, AZ