Lycoming 0-235 L2C

Lycoming 0-235 L2C

Postby planecrazzzy » Tue Dec 29, 2009 5:45 pm

Holy Cow... I found an Engine....  A guy offered it at a Bargin Price.

I found it on Barnstormers... The guy had an ad.... But he didn't reply right away...

So I placed a "WANTED" ad ( free under 100  letters )

The next morning... the guy I wrote to made the great offer... and I bought the engine...

(  It was a 4 hr drive to Iowa.... 1/2 hr to load it and pay for it....  4 hrs back to Mpls. )

But I had other people calling me and writing me about a whole bunch of other 0-235 engines...

You might keep that in mind when "YOUR" looking for an engine....
.
.
             Here's some pictures of bringing my "Baby" home....

                Gotta Fly...
                                 Mike & "Jaz" in MN
.
.
Attachments
Lycoming 0-235  L2C 002.jpg
Lycoming 0-235 L2C 002.jpg (118.81 KiB) Viewed 6411 times
Lycoming 0-235  L2C 003.jpg
Lycoming 0-235 L2C 003.jpg (96.9 KiB) Viewed 6411 times
Lycoming 0-235  L2C 005.jpg
Lycoming 0-235 L2C 005.jpg (157.08 KiB) Viewed 6411 times
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 826
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

More Pictures

Postby planecrazzzy » Tue Dec 29, 2009 5:52 pm

Here's a few more pictures...

Also... He threw in the Spinner and base plate....

The engine came out of a Cessna 152   ( 1,520 hrs )

It has a Dynafocal engine mount... I like this better...
.
                   Gotta Fly...
Attachments
Lycoming 0-235  L2C 013.jpg
Lycoming 0-235 L2C 013.jpg (116.18 KiB) Viewed 6409 times
Lycoming 0-235  L2C 008.jpg
Lycoming 0-235 L2C 008.jpg (121.2 KiB) Viewed 6409 times
Lycoming 0-235  L2C 006.jpg
Lycoming 0-235 L2C 006.jpg (117.02 KiB) Viewed 6409 times
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 826
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: Lycoming 0-235 L2C ( Mike )

Postby planecrazzzy » Thu Apr 08, 2010 6:37 pm

I made the dynafocal mount fit my landing gear on my Buttercup.

I bolted the gear back on the Jig , Used it to hold the engine mount in the exact position...

I tried the mount by putting it on the engine , While the engine was hanging from the rafters...

Once things fit good , Welded everything... and put the gear back on the plane...

Then mounted the engine....

Gotta Fly...
.
.
Attachments
Dynafocal Engine Mount 020.jpg
Dynafocal Engine Mount 022.jpg
Dynafocal Engine Mount 023.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 826
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: Lycoming 0-235 L2C ( Mike )

Postby planecrazzzy » Thu Apr 08, 2010 6:42 pm

Here's more Pix
Engine on plane - First time 001.jpg
Engine on plane - First time 004.jpg
Engine on plane - First time 005.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 826
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: Lycoming 0-235 L2C ( Mike )

Postby Sean_Caranna » Sat Apr 10, 2010 8:57 am

Nice! I was trying to find an O-235-L2C to do a low time engine swap for my 152 but nothing ever panned out. Maybe I should try again.
"I'll have what the gentleman on the floor is having."
User avatar
Sean_Caranna
Owner
 
Posts: 231
Joined: Thu Aug 12, 2004 12:34 am
Location: Daytona Beach, FL

Re: Lycoming 0-235 L2C ( Mike )

Postby planecrazzzy » Fri Dec 31, 2010 9:46 pm

Hi Sean,
Can you just imagine how this Buttercup is going to perform with this engine..... Wow...

I've bought my Prop from Craig "Catto"..... it's a Climb Prop - 66" X 46

I should be good for LSA

Gotta Fly...
.
.
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 826
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: Lycoming 0-235 L2C

Postby planecrazzzy » Sat Apr 14, 2018 11:51 am

Looks like I forgot to post about the Exhaust Pipes...
During the hook-up of Carn Heat and Cabin Heat we'll get real close to them.
.
Here's some pictures of the Air box I'm making.
I got some pictures of one that gave me a good idea how to make one.

Notes:
This hangs on the Engine... Keep it Close , Keep it light, Keep it simple.
.
the Guy gave me a Tip.... Be sure you can get to the Carb Nuts,,,.
.
.
.
So, Cold air or Warm...Small and Light , Reach the Nuts for tightening and safety ?

Here we go , I measured a strip of aluminum to make a tube,
I want the "Scat" to go at this Angle towards the Exhaust pipes
The angle also allows the "Rocking" of the engine on the scat tubing

When I rolled the Aluminum piece... It only goes so far.
I wrote on it with a Marker...then Tied a Wire around it and heated it until the marker disappeared
This gives the Aluminum a new start , and can be formed again..

Making a nice tube.
.
Gotta Fly...
.
.
Attachments
Air Intake (5).JPG
Air Intake (6).JPG
Air Intake (7).JPG
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 826
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: Lycoming 0-235 L2C

Postby planecrazzzy » Sat Apr 14, 2018 12:49 pm

.
After I guess where it goes , I tack welded it in place.
After Bolting it up , I see I need to slant it more.
This put a large opening on the back side.
I could have just welded the Gap , instead I cut a small piece of aluminum
and rolled it...fit it.

It looks like it cleaned up good.
.
Gotta Fly...
.
.
Attachments
Air Intake (8).JPG
Air Intake (9).JPG
Air Intake (11).JPG
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 826
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: Lycoming 0-235 L2C

Postby planecrazzzy » Sun Apr 15, 2018 3:37 pm

.
Today was messed up at first...
My Flap sides were supposed to be bent the opposite way...
Reminds me about the Guy in Alabama they called the Aluminum Butcher...
.
Mine was a small piece I had that I was going to TRY to make it work...
Since then , I'm back to paper mock-up...

The Bottom skin needs better fit...
It slides in place last ... Safety wire ?

Gotta Fly...
Attachments
Air Intake (16).JPG
Air Intake (15).JPG
Air Intake (12).JPG
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 826
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: Lycoming 0-235 L2C

Postby planecrazzzy » Mon Apr 16, 2018 6:59 pm

.
I got the paper mock-up converted to Aluminum...
another time the keystock in the lower die helped with a tight bend (Fades to a point)

I put some gussets on each side of the Box.
I left them long to help hold the cable in place.

I got the bottom cover to interlink with the Box , I still need to make sure it can't back out...
Maybe just a small safety wire will do it.
.
.
Gotta Fly...
.
.
Attachments
Air Intake (19).JPG
Air Intake (20).JPG
Air Intake (21).JPG
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 826
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: Lycoming 0-235 L2C

Postby planecrazzzy » Thu Apr 19, 2018 3:49 pm

.
I have met the demands...
The bottom cover slides in place last... It has a spring clip that keeps it in-place.
.
I've kept it light and simple...
.
Gotta Fly...
.
.
Attachments
Air Intake (36).JPG
Air Intake (37).JPG
Air Intake (39).JPG
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 826
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota


Return to Mike's Buttercup project