(22) Cowl ( Mike )

(22) Cowl ( Mike )

Postby planecrazzzy » Wed Jan 26, 2011 10:56 am

Hey Guys,
OK, This is a Challenge.... This will make the "Look" of this Aircraft....

I'm picturing a sleek Tailwind look.... I've got a good Start...

I bought a Nose Cowl from Blankity Blank...

I took his contact info off this Thread....

He has raised the price of the Nose Bowl to a ridiculous amount...

Same with the Spinner...

..
. Now , I'm working on putting brackets in place.... Once they are secured in position...

I will split the Cowl.... Top half and Bottom half...

Then it's a matter of sheeting the Fuselage to the cowl...
.
.
Gotta Fly...
Mike & "Jaz" the Flying Dog
.
.
In these pictures... First , I needed to secure a top "Lip" for the cowling.... ( I had to remove the engine and Firewall to do this )

Second... The cowling was cut a little crooked... I squared it and trimmed it...

Then , in order to see where I'm going to split it , I mounted it into it's position....

I drew a few lay-out lines on it , using some lines on the Firewall....

Now , the splice in the cowl should "line up" with the Cowling "Half's"
.
Attachments
Cowling 001.jpg
Cowling 002.jpg
Cowling 003.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Wed Jan 26, 2011 11:03 am

Hey Guys,
.


Working on Splitting the Nose Cowl...

Once I get all the hardware in place , Then I will make the cut...

These pieces seem to curve in every direction...

The tools used are : Shear , Roller , Beader , Shrinker , English Wheel , and Ball Peen Hammer...
.
.
. Gotta Fly...
.
...
Attachments
Cowling 005.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Tue Feb 01, 2011 9:19 pm

Hey Guys,
I got the hardware in place and the cowl "split"
.
Gotta Fly...
Attachments
Cowling 008.jpg
Cowling 009.jpg
Cowling 011.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Tue Feb 01, 2011 9:26 pm

Hey Guys,
I put the nose cowl "in place" ... and took some measurements...

There were too many angles and curves. So I used some paper to get a pattern...

Some places I added a little extra... I'll trim to fit after the bottom of the cowl

starts coming together...
.
.
Gotta Fly...
.
.
Attachments
Cowling 012.jpg
Cowling 013.jpg
Cowling 014.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Tue Feb 01, 2011 9:29 pm

Hey Guys,
Getting the general shape...

I like how it's turning out...
Gotta Fly...
.
.
.
.
Attachments
Cowling 015.jpg
Cowling 016.jpg
Cowling 017.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Tue Feb 01, 2011 9:36 pm

Hey Guys,
I've got the two top pieces shaped pretty good...

I'll need a lot more detail work on them...

Gotta Fly...
Mike & "Jaz" the Flying Dog
.
.
.
.
Attachments
Cowling 018.jpg
Cowling 019.jpg
Cowling 020.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Thu Feb 03, 2011 8:18 pm

Hey Guys,

Making the center "Hump" on the cowl... I tried using the rollers to shape it...

The 6061 was curling on the edges , but the middle needed a lot more...

So I shaped it on the English Wheel ( with the Rubber Wheel )

This should stiffen up the center of the cowl...

I'm going to end up with a aluminum edge on both sides of the cone shape/ hump

I'll put a slight taper to the lip.... and finish it with Bondo...
.
.
Also , I'm going to overlap the nose cowl "hump".... This will give the cone a straight shot...

It should look good...
.
.
Gotta Fly...
Mike & "Jaz" in MN
..

.
Attachments
Cowling 021.jpg
Cowling 022.jpg
Cowling 023.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Sat Feb 05, 2011 9:29 am

Hey Guys,
First , I need to connect both upper half's of the cowling.... I used those tiny 3/32" rivets

and tapped them with a hammer...

The overlap was about an inch... my rivet patten was like a "W".... it's strong....it's one piece now.
.
.
The rivets will be hidden by the center hump/cone shape...

I put the flush part of the rivet on the inside... that's where they will be seen.
.
.
Gotta Fly...
Mike & "Jaz" in MN
.
.
.
Attachments
Cowling 024.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Sat Feb 05, 2011 9:47 am

Hey Guys,
.
Next , I need to "fit" the cone area.

I'll get it close , and work with some Bondo later to blend the edges...

This piece really helps add strength to the aluminum in the middle area....

Instead of forming it "to" the nose cowl "hump"... I overlapped it.
.
.
This will give me a cleaner "line"... and I think it's stronger.
.
.
I think the Cowl is a pretty important part of the "Look" of the plane...

Also , The "Top" half is the most important of that...

I like the way this is turning out... It's giving me that fast "Tailwind" look....
.

.
Gotta Fly...
.
.
Attachments
Cowling 028.jpg
Cowling 029.jpg
Cowling 030.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Wed Feb 09, 2011 12:16 pm

Hey Guys,
I took some time to clean up the garage , and fixed a couple tools...

After looking at the lower cowl area several times... I put some paper on the lower area

to get a better idea of what to do. At first , It looked like crap !

But I made a few marks , took it down and trimmed it....

It's looking much better , something I can work with...

I need to take it down again and tape the area around the gear...

Once I get the pattern close , I'll trace it onto Aluminum...

These won't cover the whole bottom... The center section will be a flat piece....

These side pieces will have all the curves and bends in them....

I think it'll be easier to work with this way....
.
Gotta Fly...
Mike & "Jaz" the Flying Dog
.
.
Attachments
Cowling 031.jpg
Cowling 032.jpg
Cowling 033.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Thu Feb 10, 2011 10:45 pm

Hey Guys,
I tried the pattern on both sides... looks good.

I've made it bigger in places... The Cowling will be trimmed after it's in place.

This will give it good lines...

After "Lay-out" I curved it using the English Wheel... with an 8" rubber wheel in place of the Steel one...
.
Gotta Fly...
.
.
Attachments
Cowling 034.jpg
Cowling 035.jpg
Cowling 036.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Thu Feb 10, 2011 10:54 pm

Hey Guys,
These pieces shaped up fast... This is a ruff fit... But I like it...
.
.
Gotta Fly...
.
.
.
Attachments
Cowling 037.jpg
Cowling 038.jpg
Cowling 039.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Thu Feb 10, 2011 11:01 pm

Hey Guys,
A lot of cross checking.... and I've got a few Cleco's in place on the lower cowling...

Gotta Fly...
Attachments
Cowling 041.jpg
Cowling 042.jpg
Cowling 043.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Sat Feb 12, 2011 9:29 am

Hey Guys,
I got enough Cleco's in the lower cowl to take the top half "off"...

It worked like it's supposed to , I made a few marks and trimmed a few more places...

I put the top back on... it is SOLID...

There aren't any structural arms... But the shell is very sturdy.

I still need to put a few more mounting screws on the top Firewall area...

and the upper cowl will get a couple on the sides...
.
.
Gotta Fly...
Mike & "Jaz" the Flying Dog
.
.
.
Attachments
Cowling 045.jpg
Cowling 046.jpg
Cowling 047.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Re: (22) Cowl ( Mike )

Postby planecrazzzy » Mon Feb 14, 2011 8:29 pm

Hey Guys,
A few pix...

I made a channel to hold the side area , bowed out slightly....

It helps "Stiffen up" the flimsy side area...
Gotta Fly...
.
.
.
Attachments
Cowling 049 (2).jpg
Cowling 050.jpg
Cowling 051.jpg
Sometimes you just have to take the leap
and build your wings on the way down...
                Gotta Fly...
User avatar
planecrazzzy
Site Admin
 
Posts: 758
Joined: Sat Jan 01, 2005 1:23 pm
Location: Minnesota

Next

Return to Mike's Buttercup project