Verticle fin rivet ??

For general discussion of the Just Aircraft family of aircraft.
Includes: Highlander, Escapade, Summit and SuperSTOL.

Moderator: scubarider2

Verticle fin rivet ??

Postby b1x4nqb » Tue Jan 01, 2008 2:35 pm

Hey, I just came in from putting layers and layers of glue on.  As I was crossing the rear verticle fin I was wondering about putting a rivet right where the verticle fin inserts into the base on the trailing inside edge.  I went back and didn't see anything in the book and just thought I would double check with you guys.  I covered the bottom last evening, will finish insulating and wrap the sides this afternoon after a long lunch break.  

On a different note, I am going to switch from Superflite to Polyfiber from here on out after the body and while doing the wings.  Definetely for the paint process after talking to some who have a lot of cracking with the superflite system.  Anybody else using the Polyfiber system?
Image
b1x4nqb
Veteran Member
 
Posts: 282
Joined: Mon Aug 14, 2006 11:53 am
Location: Orwigsburg, PA

vin

Postby Gary H » Tue Jan 01, 2008 3:39 pm

I think the book says to drill and put a AN 3 bolt in there.  I used the poly fiber, It's OK, good shinney gloss on the paint. It seems that all kinds will crack after a period of time. Once you start with a system I would stick with it.
Will fly for food!!
User avatar
Gary H
Veteran Member
 
Posts: 256
Joined: Fri Sep 29, 2006 1:18 am
Location: Othello, WA

Postby Dave Krall CFII SEL SES » Tue Jan 01, 2008 5:26 pm

I'm using bolts, just so the fin/rudder can come off quickly if I want to get it into a low trailer or garage/hangar.
Dave Krall CFII SEL SES
Veteran Member
 
Posts: 922
Joined: Wed Mar 14, 2007 11:29 pm
Location: Seattle WA

Vertical Fin Attachment

Postby Wes » Tue Jan 01, 2008 6:01 pm

Paul,
I also couldn't find anything in the build manual about attaching the rear fin tube to the fuselage, so I assumed a bolt was not needed. I agonized for a while and finally came up with a "roll" pin arrangement that doesn't show. See grainy photo. I think it was about an 1/8 diam pin (now fabric covered).

Wes
Attachments
Vert Fin Attach.jpg
Vert Fin Attach.jpg (45.25 KiB) Viewed 1934 times
Kit # 95
Low and Slow - The only way to go!
User avatar
Wes
Premium Member
 
Posts: 231
Joined: Mon Jan 23, 2006 10:32 pm
Location: Satellite Bch, Florida

Postby Uwe Jens » Tue Jan 01, 2008 9:01 pm

Hi Paul
When I was building the rudder, I realized that the vertical fin entered a little more than the normal position. I was afraid that once I cover the fuselage and tautening the fabric the vertical fin will enter into the fuselage, getting out of the normal positioning. ( Hinge coincidence) THis is the reason I decided to place two ribbets, one on each side,  just to adjust the piece on the place.  I also looked into the manual and did not find anything respecting on the subject.
Regards,
Uwe/.
Uwe Jens
Seasoned Member
 
Posts: 82
Joined: Mon Aug 28, 2006 2:06 pm
Location: Salcedo-Cotopaxi-Ecuador

Postby Johnny C! » Tue Jan 01, 2008 9:27 pm

Hey Gang!
 I guess Troy or Jamie told me to put in
two rivets. I did them at about a 45 degree
from the center line, so that they wouldn't
show after covering. Sort of in front of the
position where the roll pin is in Wes' pic.
I can post a photo, if you want to see
their position.

Good Luck!

John
There are many things that happen really fast when you are
flying an airplane. There is no sense in rushing any of the others.

I would much rather be looking down at the runway, than up at it.

Duane Sorenson & Rick Norton Gone West 6/8/09. Godspeed
User avatar
Johnny C!
Veteran Member
 
Posts: 820
Joined: Thu Sep 07, 2006 9:55 am
Location: Brevard, NC


Return to Just Aircraft