I will try and post what I have for weight and balance. Let's see if this works. I followed a pretty easy process with three low profile bathroom scales. I followed the steps in one of my magazines which also gave a website that does all the calculations for you. Was pretty neat. I can get that info for you if you like. I bet you could probably just do a google search and find some good sites as well. I even thin the EAA website has a good one.
Dennis
I AM IN THE AIR
- scubarider2
- Topic Moderator
- Posts: 1086
- Joined: Mon Jan 28, 2008 7:03 pm
- Location: Cleveland, GA
weight and balance
You do not have the required permissions to view the files attached to this post.
-
- Veteran Member
- Posts: 184
- Joined: Thu Aug 17, 2006 12:20 am
Dennis,
I looked at your weight and balance sheet. The acceptable CG for the escapade is 9" to 15.5" aft of datum. I think that based on the numbers for weights the plane is ok, but there is something wrong with the sheet you did.
I calculated the empty cg at 10.69" AOD, the solo weight CG is 11.88" AOD, and the fully loaded CG is 13.93" AOD.
There is a weight and balance sheet in the build manual on page B-3. The arm lengths are listed on B-2.
Check it out and let us know.
Dave
I looked at your weight and balance sheet. The acceptable CG for the escapade is 9" to 15.5" aft of datum. I think that based on the numbers for weights the plane is ok, but there is something wrong with the sheet you did.
I calculated the empty cg at 10.69" AOD, the solo weight CG is 11.88" AOD, and the fully loaded CG is 13.93" AOD.
There is a weight and balance sheet in the build manual on page B-3. The arm lengths are listed on B-2.
Check it out and let us know.
Dave
-
- Veteran Member
- Posts: 922
- Joined: Wed Mar 14, 2007 11:29 pm
- Location: Seattle WA
- scubarider2
- Topic Moderator
- Posts: 1086
- Joined: Mon Jan 28, 2008 7:03 pm
- Location: Cleveland, GA
Dave
Thanks Dave. I will have to take a look this weekend. I don't think my manual said anything about weight and balance, just a blank couple pages. I did my own measurements and like I said just plugged it into the program on the website. I will have to look and get back to you. Would be very interested to know if I did it right or not. Does not sound like it. :oops: But your figures look more like what it should be.
Dennis
Dennis
- scubarider2
- Topic Moderator
- Posts: 1086
- Joined: Mon Jan 28, 2008 7:03 pm
- Location: Cleveland, GA
After more thought
Thanks Dave, after looking again and using the data found in the instruction manual I have recalculated the CG for the Escapade {Tequila Sunrise}. Please find attached.
You do not have the required permissions to view the files attached to this post.
-
- Veteran Member
- Posts: 282
- Joined: Mon Aug 14, 2006 11:53 am
- Location: Orwigsburg, PA
- scubarider2
- Topic Moderator
- Posts: 1086
- Joined: Mon Jan 28, 2008 7:03 pm
- Location: Cleveland, GA
Yep
Yep, it is in another post. Had the inspection from the same person that does some of the inspections out at the Wahalla site. He was really understanding about getting it done before the original deadline for transitioning fat ultralights. It just seemed a smoother process that way. So yes, I got it done as an ESLA. Not sure if that is even possible now. It just worked out for me. Right timing. The inspection was more paperwork than anything sense he was very familiar with the Escapade. He first gave me the paperwork for JA to fill out for certification of ESLA. When I called to see about getting that done, they said they have not done the necessary paperwork on their end for ESLA. So I went back to my DAR and asked him if we could just do it like everyone else out at my airport with transitioning ultralights. He said sure. So got it done that way.
Dennis
Dennis