Hey Guys,
Just a few Pictures on the process of my Firewall...
Since a lot of people like it... I'll try to explain a little about it.... it's easy to do
.
.
First , I made it from 24 ga Stainless Steel.... ( .024 )
I trimmed it to size before putting the pattern on it ( Engine Turning )
I made a grid that measured 1-1/8" squares....
My Scuff pads were 2 inch..... This way , I didn't wipe out the next row of marks...
One row , you center where the lines "Cross"...
Next row , you go inbetween where they cross....
"MY" project... I went from right to left....
It doesn't matter if it's from left to right....But which ever way you start...
That's the way it needs to be done , the whole way....
.
. Gotta Fly...
.
.
Wings Forum
Forum for homebuilt experimental & light sport aircraft pilots, owners, & builders.
(14) Firewall ( Mike )
10 posts
• Page 1 of 1
(14) Firewall ( Mike )
by planecrazzzy » Thu Jan 21, 2010 10:22 pm
- Attachments
-
- Firewall 001.jpg (81.59 KiB) Viewed 5503 times
-
- Firewall 002.jpg (107.38 KiB) Viewed 5503 times
-
- Firewall 003.jpg (147.34 KiB) Viewed 5503 times
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
-
planecrazzzy - Site Admin
- Posts: 822
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
...
by planecrazzzy » Thu Jan 21, 2010 10:25 pm
...
- Attachments
-
- Firewall 005.jpg (140.15 KiB) Viewed 5502 times
-
- Firewall 006.jpg (145.07 KiB) Viewed 5502 times
-
- Firewall 007.jpg (137.37 KiB) Viewed 5502 times
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
-
planecrazzzy - Site Admin
- Posts: 822
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
.
by planecrazzzy » Thu Jan 21, 2010 10:27 pm
..
- Attachments
-
- Firewall 008.jpg (127.01 KiB) Viewed 5501 times
-
- Firewall 009.jpg (127.86 KiB) Viewed 5501 times
-
- Firewall 010.jpg (127.78 KiB) Viewed 5501 times
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
-
planecrazzzy - Site Admin
- Posts: 822
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
.
by planecrazzzy » Thu Jan 21, 2010 10:29 pm
...
- Attachments
-
- Firewall 011.jpg (97.55 KiB) Viewed 5500 times
-
- Firewall 012.jpg (129.76 KiB) Viewed 5500 times
-
- Firewall 013.jpg (124.5 KiB) Viewed 5500 times
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
-
planecrazzzy - Site Admin
- Posts: 822
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
..
by planecrazzzy » Thu Jan 21, 2010 10:31 pm
....
- Attachments
-
- Firewall 014.jpg (152.78 KiB) Viewed 5499 times
-
- Firewall 016.jpg (152.03 KiB) Viewed 5499 times
-
- Firewall 017.jpg (132.71 KiB) Viewed 5499 times
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
-
planecrazzzy - Site Admin
- Posts: 822
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
..
by planecrazzzy » Thu Jan 21, 2010 10:37 pm
The Bottom Lip was bent first... Then the firewall was put into position...
Then the holes were marked with a transfer punch...
Holes were drilled... then the Firewall was bolted in place to check
where to make the final bends on each side , and the top...
.
.
After the final bends and checking the "fit"
The top corners of the Firewall were welded and cleaned up...
Then the holes were marked with a transfer punch...
Holes were drilled... then the Firewall was bolted in place to check
where to make the final bends on each side , and the top...
.
.
After the final bends and checking the "fit"
The top corners of the Firewall were welded and cleaned up...
- Attachments
-
- Firewall 018.jpg (122.99 KiB) Viewed 5498 times
-
- Firewall 019.jpg (124.22 KiB) Viewed 5498 times
-
- Firewall 020.jpg (133.12 KiB) Viewed 5498 times
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
-
planecrazzzy - Site Admin
- Posts: 822
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
...
by planecrazzzy » Thu Jan 21, 2010 10:39 pm
...
- Attachments
-
- Firewall 021.jpg (119.48 KiB) Viewed 5497 times
-
- Firewall 022.jpg (120.38 KiB) Viewed 5497 times
-
- Firewall 023.jpg (129.33 KiB) Viewed 5497 times
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
-
planecrazzzy - Site Admin
- Posts: 822
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
Last picture
by planecrazzzy » Thu Jan 21, 2010 10:44 pm
Last but not least , this picture shows how I tilted the firewall forward...
Also... I made it an inch taller on the whole radius...
This will help slope the windscreen more... Less drag
and I like the way the Tailwinds look that use this technic
.
.
Gotta Fly...
Mike & "Jaz" the Flying Dog
.
.
.
Also... I made it an inch taller on the whole radius...
This will help slope the windscreen more... Less drag
and I like the way the Tailwinds look that use this technic
.
.
Gotta Fly...
Mike & "Jaz" the Flying Dog
.
.
.
- Attachments
-
- Firewall 024.jpg (121.15 KiB) Viewed 5496 times
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
-
planecrazzzy - Site Admin
- Posts: 822
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
Re: Firewall ( Mike )
by Sean_Caranna » Sat Feb 13, 2010 2:15 pm
That looks absolutely outstanding!
"I'll have what the gentleman on the floor is having."
-
Sean_Caranna - Owner
- Posts: 231
- Joined: Thu Aug 12, 2004 12:34 am
- Location: Daytona Beach, FL
Re: Firewall ( Mike )
by planecrazzzy » Fri Dec 31, 2010 9:42 pm
Thanks Sean,
This is what it's all about... Taking an regular piece of material , and making something special...
But this design has it's good points.... Hiding Dents , scratches , and dirt...
Gotta Fly...
Mike & "Jaz" the Flying Dog
.
.
PS I see yer looking for a new plane to build.... Buttercup is pretty easy... a lot of History too ( 1938 )
.
.
.
This is what it's all about... Taking an regular piece of material , and making something special...
But this design has it's good points.... Hiding Dents , scratches , and dirt...
Gotta Fly...
Mike & "Jaz" the Flying Dog
.
.
PS I see yer looking for a new plane to build.... Buttercup is pretty easy... a lot of History too ( 1938 )
.
.
.
- Attachments
-
Last bumped by planecrazzzy on Fri Dec 31, 2010 9:42 pm.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
-
planecrazzzy - Site Admin
- Posts: 822
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
10 posts
• Page 1 of 1