Fish Scales (Engine Turning)....Floor pan first....Then ?
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Fish Scales (Engine Turning)....Floor pan first....Then ?
Hey Guys,
I learned something watching one of those shows where they were building a Fire engine....
They said the swirling "Fish Scales" had a purpose....They weren't just done for looks....
The purpose......they HIDE scratches....
I didn't want to put carpet on my floor pan , and it was beginning to get scratched up....
and because I just think "Fish Scaling" looks cool too.... I did it....Here's some pictures , I took them in different stages
so you can see how easy they are to do....
Two "Tips" ....One , I sprayed it with starting fluid , so my sharpie would stick....
( Wiping it with Lacquer thinner works too )
and two , I sprayed it with WD-40 so that the scuff pad wouldn't gum up and start Gauling the aluminum....
( Now , I put WD 40 in a paint cap.... Dip the scuff pad ... Then lift and spin off the excess fluid )
Gotta Fly...
Mike & "Jaz" in MN
I learned something watching one of those shows where they were building a Fire engine....
They said the swirling "Fish Scales" had a purpose....They weren't just done for looks....
The purpose......they HIDE scratches....
I didn't want to put carpet on my floor pan , and it was beginning to get scratched up....
and because I just think "Fish Scaling" looks cool too.... I did it....Here's some pictures , I took them in different stages
so you can see how easy they are to do....
Two "Tips" ....One , I sprayed it with starting fluid , so my sharpie would stick....
( Wiping it with Lacquer thinner works too )
and two , I sprayed it with WD-40 so that the scuff pad wouldn't gum up and start Gauling the aluminum....
( Now , I put WD 40 in a paint cap.... Dip the scuff pad ... Then lift and spin off the excess fluid )
Gotta Fly...
Mike & "Jaz" in MN
You do not have the required permissions to view the files attached to this post.
Last edited by planecrazzzy on Sun Feb 04, 2007 6:44 pm, edited 1 time in total.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Fish Scales....Floor pan first....Then?
more pics
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Fish Scales....Floor pan first....Then?
mo pics
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Fish scales on Lift Struts
I don't want to go CRAZY with these Fish Scales....But my Lift Struts have alot of scratches on them...
I tried to have a smooth shiny finish on them , but they get handled too much , they have to be taken off the plane every time the Wings are folded....
What "Hides" scratches...... Fish Scales...
I tried to have a smooth shiny finish on them , but they get handled too much , they have to be taken off the plane every time the Wings are folded....
What "Hides" scratches...... Fish Scales...
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Fish scales on Lift Struts
pictures
You do not have the required permissions to view the files attached to this post.
Last edited by planecrazzzy on Sun Feb 04, 2007 3:05 pm, edited 1 time in total.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Machine turning ?
The only machine around is the die grinder w/ scuff pad in my hand....
I've seen this done with a machine , and it's alot more precise then what I'm doin.... but I don't think these Lift struts
could be done that way.... too much of a hump to go over...
I've also heard it called "Jeweling" but I think that's on Rifles ect...
Gotta Fly...
Mike in MN
I've seen this done with a machine , and it's alot more precise then what I'm doin.... but I don't think these Lift struts
could be done that way.... too much of a hump to go over...
I've also heard it called "Jeweling" but I think that's on Rifles ect...
Gotta Fly...
Mike in MN
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- KevinC
- Veteran Member
- Posts: 447
- Joined: Fri Aug 19, 2005 12:42 am
- Location: Prosser, Washington
fish scaling
that really does look good. I tried it the other night, but found that the die grinder wanted to make an uneven circle and skip off the work. In addition, it tended to polish rather than scuff circles.
What am I missing? There must be some part of the technique that I'm not getting.
Not a metal worker :oops: -
Kevin
What am I missing? There must be some part of the technique that I'm not getting.
Not a metal worker :oops: -
Kevin
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Re: fish scaling
Hi Kevin,
Were you using a "straight" die grinder...... I'm using a 90 degree die grinder....I'll bet it's easier to keep in control.
I just got done finishing my 2nd Lift Strut......Man , what'a bear going over that hump....I got better as I went ( typical )
maybe , if yours is inline....you could make a 90 degree handle, and clamp it on....( bent flat bar , 2-Band clamp )
The "Formula" that "I" used was..... it's a 2inch pad , so I made 1 inch ( plus ) squares....That seems to space it just right.
Are you using "Scuff pads" or sanding disc...?
Gotta Fly...
Mike in MN
Were you using a "straight" die grinder...... I'm using a 90 degree die grinder....I'll bet it's easier to keep in control.
I just got done finishing my 2nd Lift Strut......Man , what'a bear going over that hump....I got better as I went ( typical )
maybe , if yours is inline....you could make a 90 degree handle, and clamp it on....( bent flat bar , 2-Band clamp )
The "Formula" that "I" used was..... it's a 2inch pad , so I made 1 inch ( plus ) squares....That seems to space it just right.
Are you using "Scuff pads" or sanding disc...?
Gotta Fly...
Mike in MN
KevinC wrote:that really does look good. I tried it the other night, but found that the die grinder wanted to make an uneven circle and skip off the work. In addition, it tended to polish rather than scuff circles.
What am I missing? There must be some part of the technique that I'm not getting.
Not a metal worker :oops: -
Kevin
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...