Hey Guys,
You might have read about the trouble I had with my Windscreen on my second flight.... :shock:
Someday I'll make a "Full enclosure" , but for now I put a brace in the windscreen....
I cut the Aluminum Tubing at 4' 10" and bent it around something 15" Dia. :?
I put some tape on the Lexan to make my marks.... :?:
I used 1/8" SS rivets , and I drilled the Lexan bigger ( 5/32 ) :)
Afterwards I pulled off the tape , some of the adhesive stayed on... :evil:
I cleaned it off with Mineral Spirits....
Then I cleaned the whole windscreen with some of my disposable CD cleaner cloths....( Rubbing Alcohol ) :D
It cleaned it VERY GOOD and didn't scratch it....
Here's some Pictures....
Sagging Windscreen Brace
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Sagging Windscreen Brace
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
More Pictures
Here's the rest of the pictures...
Gotta Fly...
Mike in MN / N381PM
Gotta Fly...
Mike in MN / N381PM
You do not have the required permissions to view the files attached to this post.
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...
-
- New Member
- Posts: 5
- Joined: Sat Mar 25, 2006 7:22 am
- Location: California
Hi, Mike
That sure is a good lookin little airplane you got. I checked out your building Log on your website.
Nice Job.
I am in the process of re-building a Firestar, and some day I hope it looks something like yours. It got flipped over in a wind storm, and damaged the left wing, elevator, & rudder.
Here are some pics of the Fixer upper I just started working on. Theres more info on my Introduction post.
Right now, I am trying to figure out a good way to remove the rivets, from the hinges, without distorting the whole size, so that when I go to re-cover I can use the same wholes with new hinges. Would you happen to know a good way to do this?
I also need to remove the old polytak that is on the surface. Any suggestions on solvents or stripper that will clean the gunk off?
Thanks, Chris
That sure is a good lookin little airplane you got. I checked out your building Log on your website.
Nice Job.
I am in the process of re-building a Firestar, and some day I hope it looks something like yours. It got flipped over in a wind storm, and damaged the left wing, elevator, & rudder.
Here are some pics of the Fixer upper I just started working on. Theres more info on my Introduction post.
Right now, I am trying to figure out a good way to remove the rivets, from the hinges, without distorting the whole size, so that when I go to re-cover I can use the same wholes with new hinges. Would you happen to know a good way to do this?
I also need to remove the old polytak that is on the surface. Any suggestions on solvents or stripper that will clean the gunk off?
Thanks, Chris
You do not have the required permissions to view the files attached to this post.
If you want something done, the way you want it done, Do it Yourself!!!
- planecrazzzy
- Site Admin
- Posts: 1154
- Joined: Sat Jan 01, 2005 1:23 pm
- Location: Minnesota
- Contact:
Hi Chris,
MEK is what you need for that "poly tac " clean up...... It's what you'll use later to "thin" the Glue
and I also used it to "thin" my Poly color coats....Special care should be taken....Get a GOOD charcoal resperator
and when you start to "smell" the MEK....Change the filters.....It's some BAD brain killin shit........
MEK - Methal Ethal Keytone ( my spelling is probly NOT right ) Not all hardware stores have it...Look around
Rivets.....Go to the Kolb List and throw the question out there......Post these pictures too....and YES, you want to use the SAME holes..... Do you have the Blueprints AND the Builders Manual ????
Also, here's an address for Stits process, "Poly" supplies
http://www.polyfiber.com/where/
Somebody that all the Kolb Guys like , and call for help is at that site.....He's Jim....Real helpful and Friendly...
www.aircrafttechsupport.com
Well,
Sounds like you'll be busy for a while...
Gotta Fly...
Mike in MN / N381PM
.
.
.
MEK is what you need for that "poly tac " clean up...... It's what you'll use later to "thin" the Glue
and I also used it to "thin" my Poly color coats....Special care should be taken....Get a GOOD charcoal resperator
and when you start to "smell" the MEK....Change the filters.....It's some BAD brain killin shit........
MEK - Methal Ethal Keytone ( my spelling is probly NOT right ) Not all hardware stores have it...Look around
Rivets.....Go to the Kolb List and throw the question out there......Post these pictures too....and YES, you want to use the SAME holes..... Do you have the Blueprints AND the Builders Manual ????
Also, here's an address for Stits process, "Poly" supplies
http://www.polyfiber.com/where/
Somebody that all the Kolb Guys like , and call for help is at that site.....He's Jim....Real helpful and Friendly...
www.aircrafttechsupport.com
Well,
Sounds like you'll be busy for a while...
Gotta Fly...
Mike in MN / N381PM
.
.
.
DrHook wrote:Hi, Mike
That sure is a good lookin little airplane you got. I checked out your building Log on your website.
Nice Job.
I am in the process of re-building a Firestar, and some day I hope it looks something like yours. It got flipped over in a wind storm, and damaged the left wing, elevator, & rudder.
Here are some pics of the Fixer upper I just started working on. Theres more info on my Introduction post.
Right now, I am trying to figure out a good way to remove the rivets, from the hinges, without distorting the whole size, so that when I go to re-cover I can use the same wholes with new hinges. Would you happen to know a good way to do this?
I also need to remove the old polytak that is on the surface. Any suggestions on solvents or stripper that will clean the gunk off?
Thanks, Chris
Sometimes you just have to take the leap
and build your wings on the way down...
Gotta Fly...
and build your wings on the way down...
Gotta Fly...